Starting at the cleaning head farthest from the valve, remove test plug and flush the pipe, blocking and releasing pressure several times to ensure a clear line. Refer to instructions on Page 11. Clean the pool filter whenever pressure increases 3 psi above normal clean-filter operating pressure. When all connections are complete and it is clear that the system is holding pressure, backfill, tamp and level all trenches. Before initiating the system, open a discharge line before the valve and flush the pool pump and filtration system. Risers or stub-ups are glued into 2 (5.1 cm) Tees, 90-degree elbows, to stub-ups through the pool shell.Match the riser width to collar width. To contact Caretaker:Customer Service2580 S Decker Lake Blvd, STE 300West Valley City, UT 84119toll-free: 855.280.6465email: [emailprotected]www.caretakersystem.com. Make line trench depth sufficient to cover all pipes with 6 (15 cm) of soil. If the wall return line can also recieve water pressure from the pump, install a check valve between the Caretaker valve and wall returns to prevent water from back flowing into the valve. For Vinyl Liner Pools:Set collar fittings before clearing lines. Insert Metal Combination Tool (part #3-17-7) into collar and rotate clockwise until collar is firmly seated. Ultra-durable valve plate with ball bearings, WK000030Caretaker 6 Port Valve, 2 Inch Outlet Ports Complete. Dig trenches 8 in. Plumb 2-way valves into each discharge line so they can be pressurized to push water below the freeze zone and sealed to prevent water from coming back up into the valve. Caretaker2580 S Decker Lake Blvd, STE 300 West Valley City, UT 84119855.280.6465 toll-free | 801.906.6701 fax[emailprotected].comwww.caretakersystem.com. WARNINGInstallation of this equipment should be performed by a licensed pool contractor and conform to the National Electrical Code (NEC) . Fluidra strives to deliver the perfect pool experience that enhances comfort, enjoyment, and peace of mind for pool owners. The pump can be run through out the day at low RPMs, allowing water rotation through the filtration system. Remove the band clamp and lid. Keep the water valve secure and under pressure throughout the construction process. Check the break, width, depth, and designated step/bench locations. Install the valve above ground and the finished pool water level. Available In Store only. Excavate an area (12 in. The company has a rich heritage of innovation excellence dating back more than 100 years and markets its product lines under the leading brand names of Zodiac, Polaris, Jandy, Nature2, Caretaker, Grand Effects and Cover-Pools. Remove the cassette assembly. Use 90 elbows or tees at each head location. Install all lines with a minimum of 6 (15.2 cm) cover or in accordance with local codes. Open the valve and remove cassette assembly and packaging prior to gluing. To minimize risk of severe injury or death the filters, pumps, and heaters should not be subjected to the piping pressurization test. Stake but do not plumb lines until walls are set; plumbing lines are fed under walls. Zodiac Caretaker Revolution 6-Port Hydraulic In-Floor Cleaning System, 2" Ports | WK000030, View Cart {{shoppingcart.totalQuantityDisplay}} Item(s), #WK000030 Zodiac Caretaker Revolution Hydraulic 6-Port Valve Complete with 2" Outlet Ports, #WK000030Zodiac Caretaker Revolution Hydraulic 6-Port Valve Complete with 2" Outlet Ports. Attach the Head Removal Tool (part number 3-17-8) to the pool pole. In the event no such state or local requirement exists, the installer or maintainer must be a professional with sufficient experience in pool equipment installation and maintenance so that all of the instructions in this manual can be followed exactly. Use compressor or blower to blow water from discharge lines. This is the most durable in-floor pool cleaning valve weve ever built, said LaMont Drechsel, Vice President and General Manager, Caretaker. The 6-port valve provides dependable and efficient in-floor cleaning by maximizing water flow through strategically placed cleaning heads to give your pool a robust and thorough cleaning. Replace test plug and repeat for each riser. Zodiac Pool Systems LLC, a Fluidra company, is a global manufacturer of residential pool equipment and connected pool solutions. Reduce run times by 2 hours every 2 days until minimum cleaning time is determined. Remove any cleaning heads located above the freeze line (step or bench heads). Remove the protective caps from the collars. Consult manufacturers installation instructions. For technical assistance, contact Caretaker for assembly instructions. (0.6 cm) edge around the ring perimeter. Perimeter heads have a 1 ft. (0.3 m) overlap. If all outlet ports on the valve are not needed, double-port the line by tying the unused port into an active port. Apple is not a participant or sponsor of this promotion. If a spa is included, it will require a dedicated line from the valve. Caretaker Announces Revolution 6-Port Valve. When performing hydrostatic pressure tests or when testing for external leaks of the completed filtration and plumbing system, ensure that the maximum pressure the system is subjected to does not exceed the maximum working pressure of any of the components within the system. Failure to follow warning notices and instructions may result in property damage, personal injury, or death. Fluidra 2580 S Decker Lake Blvd, STE 300 West Valley City, UT 84119855.280.6465 toll-free | 801.906.6701 fax[emailprotected]www.caretakersystem.com. If any dimensions have changed, a new plan must be drawn to ensure cleaning and warranty.Position the valve as close as possible to the swimming pool or water feature to reduce piping and improve performance. Fine tune your system by finding the minimum speed required to fully lift the heads. Concrete or Vermiculite for Vinyl-Liner Ritz-Carlton Golf Resort, Naples Receives 2022 AI Dream Designs Honor, Check Out This Year's Dream Design Waterparks, These Family Aquatics Centers Take Dream Designs Recognition, See These Other Categories That Took Dream Designs Honors, The Cove at The Piazza Pool Awarded 2022 AI Dream Designs. WARNINGRead these instructions completely before starting the procedures. Verify all stub-ups are above the pool shell. This is the most durable in-floor pool cleaning valve built. NEW Jandy TruDose provides advanced technologies to properly maintain pool chemical levels. Ensure collar is perpendicular with pool shell; you can rotate the 2-1/2 Ultraflex collar up to 10 to accommodate a crooked 2.5 stub-up. Mark the cleaning radius around each stake to verify cleaning coverage (Figure 2). We're looking for the best and brightest to join us as we innovate, collaborate and dedicate our efforts to driving the future of the perfect pool and wellness experience. Each head has a designated nozzle that has a precise cleaning radius (see Figure 1). Attach the Head Removal Tool (part #3-17-8) to the pool pole. Ever. Replace band clamp and torque to approx. Run all feed lines to the top of the bond beam to facilitate easy valve hookup. Engineered for hassle-free maintenance, pool professionals will appreciate the ease with which Revolution can be serviced. Improper installation and/or operation will void the warranty. Press locking ring firmly into place in groove on collar fitting. If the valve must be installed below water level, check valves or manual valves on the inlet and outlet ports are required to prevent flooding of the valve. Trade Grade Series. The Caretaker system first revolutionized pool cleaning nearly 50 years ago, said Drechsel, Now, with this new Revolution that makes cleaning swifter and more streamlined for superior results, were doing it again.. To learn more about Zodiac, please visit www.zodiac.com or call 800-822-7933. Your email address will not be published. (20.3 cm) below excavation grade to accommodate setting of fittings. SAN DIEGO July, 8 2019 Caretaker, the original in-floor pool and spa self-cleaning system, is taking in-floor cleaning to new levels of efficiency with its latest innovation the Caretaker Revolution 6-Port Valve. During gunite application, leave a 1 (2.5 cm) deep x 1 (2.5 cm) wide well around each stub-up. Electrical cost savings can be gained by using a variable speed pump. Then use an inside pipe cutter to cut it again 1 in. When the pool interior is completely clean and ready for the final finish application, install the collars (see Figure 9). Size the filter to exceed the flow requirements of the certified design. Improper installation and/or operation can create an unwanted electrical hazard which can cause serious injury, property damage, or death. Cut pipe stub-up flush with the pool floor. Its passed the most rigorous tests we have ever conducted; you can be certain these valves will stand the test of time.. Use 45 and sweep elbows to improve water flow. Prepare for cold weather by plumbing the valve so it can be winterized easily. Improper installation and/or operation will void the warranty. Discharge pipes should extend 24 below the freeze zone before turning toward the pool. Before installing this product, read and follow all warning notices and instructions that accompany this product. 2020 Zodiac Pool Systems LLC - All rights reserved. WARNINGTo reduce the risk of injury, do not allow children to handle this equipment unless they are closely supervised. All applicable local installation codes and regulations must be followed. 2882 Whiptail Loop # 100 Install the discharge lines from the valve in a stacked or flat configuration. To ensure complete cleaning and to qualify for the 99% cleaning guarantee, the pool builder must fax or email a Design Fact Sheet along with a scaled pool plan for FREE In-Floor DesignService prior to plumbing the pool.Email: [emailprotected]Fax: (801)-906-6701If the pool design or dimensions change during excavation, a new design plan must be drawn, or the cleaning guarantee will be void. The Caretaker cleaning heads are designed to operate at a specific gallonage and pressure. Each Caretaker system is custom designed for the unique size and shape of your pool. Left justify heads next to sharp corners. And, if the valve should ever have a problem, it remains open eliminating dead head and protecting the plumbing, pump and filter. If a port is used as a return line, install an eyeball fitting at the pool wall to create back pressure on the line. Place winterizing plugs into collars that are above water line to prevent runoff from filling the lines and refreezing. The Revolution 6-Port Valve from Caretaker In-Floor Pool Cleaning Systems is designed to be durable, efficient and easy to service. However, the installer must follow the pipe size guidelines found on the certified pool plan which includes a minimum requirement of 2 PVC SCH40 for all floor inlets.Install the valve so that the body housing and outlet ports are above ground and the finished pool water level. Refer to the manufacturers instructions for the pumps, filters, and heaters for instructions regarding the maximum pressures the pool equipment can be subjected to. (see Figure 11). The Caretaker system replaces unsightly vacuum hoses and other stand-alone pool cleaners so your pool area is uncluttered and always ready to be enjoyed. Clear debris from all filters and pump basket. Comment document.getElementById("comment").setAttribute("id","a7b45c1eb6cb6914a7304c4dfa1aa9dc");document.getElementById("afe6277d1c").setAttribute("id","comment"); Save my name, email, and website in this browser for the next time I comment. Installation Tip: Turn collar upside down and use as a tool to press ring into place. Refer to the manufacturers instructions of the filter for proper cleaning instructions. WARNINGThis manual contains important information about the installation, operation, and safe use of this product. (4.8 cm) lower than the floor level. Lay out system so feed pipes enter the pool in the center of the wall closest to the pool equipment and valve. Perform a Hydrostatic pressure test by filling each line and the 6-Port valve with water. (tap on the perimeter periodically to ensure equal tension). To maintain flow through the heads, run the system whenever the pump is on. Use a blower assembly unit (blower, check valve, air/water supply, and connectors) to blow out debris that can gather in the plumbing during the construction process. Use a sander/grinder to sand each stub-up smooth and level with the shell finish to ensure proper glue adhesion with collar setting. Push collar firmly into pipe with a 1/4 turn. Home CARETAKER CARETAKER REVOLUTION 6-Port Valve Installation Guide, REVOLUTION6-port valveInstallation and Maintenance Guide. Consult manufacturers instructions for proper installationto protect the water valve and other pool equipment from high concentrations of chlorine or chlorine gas.Automatic Pool Cleaners: When using an automatic pool cleaner with the in-floor system, plumb the dedicated cleaner line (booster pump if applicable) before the valve (see Figure 4).Water Features, Falls and Returns: Plumb so the 6-port valve receives the GPMs mentioned in the certified design during the cleaning sessions.Filters: Use of a filter is required to maintain a warranty. Position o-ring in place and replace lid. The Caretaker-certified pool plan indicates which cleaning heads will be plumbed together to form a bank. (20.3 cm) below excavated floor) and fill with concrete to form a thrust block to eliminate movement of the cleaning head. Number the lines according to the design plan (see Figure 2). Turn on blower and water supply and direct the flow to one zone at a time. Attn: Customer Support Find a pool builder, retailer, or service professional in your area. Six hours a day is recommended. Install other check valves (as normal) to avoid spa return jets and suction lines from draining.