pressurized abrasive blaster PARTS DRAWING 19 18 16 17 16 15 12 14 11 13 10 18A 7 6 8 3 20 21 31 9 5 2 3 14 16 1 18B 16 25 18C 22 16 23 26 27A-D 24 28 23 Page #14 -- SKU 34202, No portion of this manual or any artwork contained herein may be reproduced in any, shape or form without the express written consent of Harbor Freight T. For technical questions and replacement parts, please call 1-800-444-3353. For technical questions and replacement parts, please call 1-800-444-3353. Remove the Compression Nut (2) from the Air Regulator (9). It works well for general use, but for lots of heavy rust removal I might prefer something more coarse. PRESSURIZED SANDBLASTER ASSEMBLY and OPERATING INSTRUCTIONS 3491 Mission Oaks Blvd. Use Media Regulator Knob to adjust the media flow rate. 
Other components, such as a coupler plug and quick coupler, will make operation more efficient, but are not required. For gross removal of paint and rust you may want maximum pressure on the blaster (do not exceed 125 psi safe pressure limit). sand abrasive hVn8>X$"(nHv?U@V6g }(G3:e!V5pWXE$bHCXN`PAVI"d 9cg:Y?)&gF#u8fJj%XVtq gY 5.t:$tCrZM X 01qWn5tsRNiOqG3:HAgeQO&zI !/gFw &r&OW_WYMdI6O CS BE|5v'"obeUv[?4ppc>r[H7IfYIp%~`;]Jn h1q=>[s&!8PZmuz|phZ#>iegI!KxvX TO PREVENT SERIOUSINJURY FROM ACCIDENTAL OPERATION:close all Valves, detach the air supply, safely discharge any residual air pressure in the Soda Blaster, and close all Valves again before performing any procedure in this section. Use tools with the lowest vibration when there is a choice. Poor or irregular flow of the abrasive may also be due to low air pressure or a worn Nozzle. eastwood That pressure is non functional with this unit, but it indicates a rough air consumption figure of 9.0-scfm @ 45-psi. Overall dimensions: 40''H x 24''L x 15''W
Step 1: Check to insure the abrasives are dry and clean so that they do not clog the unit. 
Do not yank compressors cord to disconnect it from the receptacle. Avoid skin exposure. This warranty gives you specific legal rights and you may also have other rights which vary from state to state. The grit goes everywhere, so don't have an open engine or gearbox in the room when doing this. Step 2: Attach the FOOT to the TANK (#1) using one of the COTTER PINS. 497A""
A"TD
.j?,\~gO.v ?@&)34q~: e y@2$J B H- 3"Kd P3. A possible short use alternative is a pillow case with a site hole cut out and fully closed goggles. Inspect compressors cord periodically and, if damaged, have them repaired by an authorized technician. Diagrams within this manual may not be drawn proportionally. We will return repaired products at our expense, but if we determine there is no defect, or that the defect resulted from causes not within the scope of our warranty, then you must bear the cost of returning the product. Open the Media Valve. As such it will work with 50%-60% duty cycle with my compressor, giving one minute of trigger time
DO NOT OVERREACH. BEFORE EACH USE, inspect the general condition of the Soda Blaster. cabinet blast homak abrasive table gallon sandblaster blasting blaster sand tank industrial air Difference is, a ball valve does not shut off automatically if you drop it. Spray the abrasive media onto the work material, moving the Nozzle from side to side. Attempting to blast aluminum sheet panels or soft brass parts is tricky business to be approached at your own risk. Wear ANSI-approved eye protection. Sand Control Valve/ Nozzle Shut Off Valve Refer to Figure 5. Keep in mind that the media tank is also a compressed air tank with a fairly large volume (about 10 gallons). Secure loose workpieces using a vise or clamps (not included) to prevent movement while working. ?,)rD&7hgq/X~s(8$b+>gT ?iadZgg[%C'Btt;LL|D( IEZT{%"F$Z)D?DCS*NEB('TF8*Du1@!d$4 When I finally take the body off the car for underbody painting there will be more grit on the heater shelf, under and around the engine, and on the suspension parts. To reduce vibration, maintain tool as explained in this manual. Step3: Attach the JOINT PIPE (#13) to the upper side port of the TANK (#1). If the blast nozzle becomes clogged during use, immediately close the media control valve at bottom of the tank. I was walking around in the grit and not wanting to touch anything. Obey the manual for the air compressor used to power this Soda Blaster. It may be appropriate to order a replacement hose for the inside of this control head, along with a few spare ceramic nozzles. blower The nozzle control valve on this unit has a thin wall rubber hose inside of a heavy plastic housing. Sand Outlet Manifold (#22) Nipple Connector Step4: Attach the other NIPPLE CONNECTOR (#16) to the other end of the SAND CONTROL VALVE. Read the ENTIRE IMPORTANT SAFETY INFORMATION section at the beginning of this manual including all text under subheadings therein before set up or use of this product. HWr6CD0q/GVZwZ;Zku$JY n;i@bqX. Step2: Attach the PRESSURE GAUGE to the top of the INTAKE MANIFOLD. Turn PRESSURE GAUGE so that its face is over the lower side hold of the INTAKE MANIFOLD. I would say read the entire user's manual, except that it is missing, so my best advice now is to read this entire memo before using the sand blaster. The pipe then splits with one pipe going to pressurize the media tank. 23n`H`3`0c`0u#"2W/
3f@4. The tank can hold up to 110 pounds of abrasive material. Likewise, always open the air control valve before opening the media control valve. 
Personal Equipment, Dirt and Cleanup:
Read and understand the 10 recommended measures below to reduce crystalline silica exposures in the workplace and prevent silicosis and silicosis related deaths. If you close all the valves and walk away it is likely to lose tank pressure through the media control valve and blast head. Nipple Connector (#16) Joint Pipe (#13) Air Cap (#12) Gasket (#11) Tank (#1) Nipple Connector (#16) Air Hose (#21) Figure 6 Top Assembly Step1: Get the Intake Valve Assembly, the Water Trap Assembly, the Tank Assembly, the TANK CAP (#12), the O-RING (#11), and the AIR HOSE (#21). Figuring about 2/3 pound of abrasive use for each minute of trigger time, a full tank could keep you working for 165 minutes of continuous use. ASSEMBLY NOTE: Use Teflon Pipe Tape on all threaded joints. Follow instructions for lubricating and changing accessories. The shop vac will clean a smooth floor in a single pass. The media control valve at the bottom of the tank seems to leak a little when shut off, probably due to being constantly exposed to the abrasive material. There will be no attempt here to turn an amateur blast operator into a skilled professional by words alone. 
Step2: Slide the HOSE CLAMPS over either side of the SAND HOSE. Right Handle (#6-R) Handle Grip (#7) Handle Bar Left Handle (#6) (#6-L) Screw (#8) Washer (#31) Nut (#9) Figure 7 Handle Bar Assembly Step1: Get out the two HANDLE BARS (#6), the two HANDLE GRIPS (#5), the four SCREWS (#8), four NUTS (#9), and four WASHERS (#31). Insert the Pickup Tube into the Tank and tighten the Bushing. DO NOT ABUSE THE POWER CORD. I didn't like the heavy handed operation of the control lever, so this may be better if it was changed to a ball valve. There is an air supply shut-off valve at the input air coupler, followed by a water separator filter and pressure gauge. WARNING! It is used to alert you to potential personal injury hazards. Wear NIOSH-approved dust mask/respirator. abrasive capacity for big jobs. This may sound like a lot of fiddling, but you should soon learn to regulate and limit the media flow to minimize clogging of the blast head. (Wrenches not included. @ Y
endstream
endobj
40 0 obj
<>
endobj
41 0 obj
<>/Font<>/ProcSet[/PDF/Text/ImageC/ImageI]/XObject<>>>/Rotate 0/Type/Page>>
endobj
42 0 obj
<>
endobj
43 0 obj
<>
endobj
44 0 obj
<>
endobj
45 0 obj
<>
endobj
46 0 obj
[/Indexed 61 0 R 255 63 0 R]
endobj
47 0 obj
[/ICCBased 59 0 R]
endobj
48 0 obj
<>
endobj
49 0 obj
<>stream
if any problems are found, do not use Soda Blaster until repaired. Wear washable or disposable protective clothes at the work site. sandblaster hopper gun Efficient pressurized blaster moves abrasives at 80 to 90 percent of air speed for real blasting power. Instructions Pertaining To A Risk Of Fire, Electric Shock, Or Injury To Persons. Release the collar. j"V09ZG&:>V x73K1b$&h88YpCi OfM+~'g%af%0CA &[q-gzrd
2@.l*8U\ZIRB)Cj%YDq(?RI%:e\jJ;s4/7R>MM3\BqRT+8OiI&%C3 ^oJ:OaBw!+j={O%IvOmM44eCi4g{P8/s@
n' VO~%q Coarser material tends to clog up the nozzle on smaller blaster units (including this one). hb```"3 Ab@Oa{$TXRZM
w(2OLyT0kWG;DW
O',s8V,a0If"m^"[=%$raD1CbE Inspect Soda Blaster before use, looking for damaged, loose, and missing parts. SAVE THIS MANUAL You will need the manual for the safety warnings and cautions, assembly instructions, operating procedures, maintenance procedures, trouble shooting, parts list, and diagram. At 50 psi this unit stops supplying abrasive material. Post signs to warn workers about the hazard and to inform them about required protective equipment. 
Wear suitable gloves to reduce the vibration effects on the user. Removing heavy rust from steel parts is a cinch, as it can ultimately remove steel from steel parts. If you have a smaller compressor (less than 15-scfm supply), there may be large swings in system pressure during use. Always wear your hood, dust mask, and heavy-duty canvas Step 2: Close the AIR SUPPLY VALVE (#18) by turning it to gloves when operating the the horizontal position. 11. Pull back on the blue Air Hose Connector (8) collar and pull out Air Hose (15). Proper ventilation in the work area is required. Use containment methods such as blast-cleaning machines and cabinets to control the hazard and protect adjacent workers from exposure. sandblaster abrasives Exposure to aluminum oxide (a dust generated from material removing processes) can result in eye, skin and breathing irritation. Trouble shooting:
Drain the moisture filter regularly. Step 4: Slide the AXLE through the hole in the bottom of the two HANDLE BARS (#6). Parts may not be interchangeable. MAINTAIN TOOLS WITH CARE. followed by one minute of pressure recovery time for the compressor. Do not use sand or other blasting materials that contain crystalline silica.Note: Use only dry and clean abrasives to avoid clogging the Soda Blaster.Note: The Nozzle size depends on grit of media used. This setup had a problem when I first used it, as the blast head would sometimes clog easily and repeatedly. Make sure all joints are securely tighten. 
angle sander polisher angle sander polisher angle sander polisher (10 pages), 6" self-vacuuming air palm sander (16 pages), Heavy duty air oscillating sander (11 pages), Manual will be automatically added to "My Manuals", Assembly and operating instructions manual, Sand Control Valve/ Nozzle Shut off Valve, Sander Central Pneumatic 35245 Assembly And Operating Instructions Manual, Sander Central Pneumatic CENTRAL PNEUMATIC 91773 Owner's Manual, Sander Central Pneumatic 66881 Set Up And Operating Instructions Manual, Sander Central Pneumatic 68152 Owner's Manual And Safety Instructions, Sander Central Pneumatic 93629 Assembly And Operating Instructions Manual, Sander Central Pneumatic 93742 Assembly And Operating Instructions Manual, Sander Central Pneumatic 42966 Assembly And Operating Instructions Manual, Sander Central Pneumatic 97055 Set Up And Operating Instructions Manual, Sander Central Pneumatic 91773 Set Up And Operating Instructions Manual, Sander Central Pneumatic 65173 Set Up And Operating Instructions Manual, Sander Central Pneumatic 93050 Assembly And Operating Instructions Manual, Sander Central Pneumatic 98895 Owner's Manual & Safety Instructions, Sander Central Pneumatic 96989 Set Up And Operating Instructions Manual, Sander Central Pneumatic 96445 Operation Instructions Manual, Sander Central Pneumatic 96573 Set Up And Operating Instructions Manual. Sand Control Valve (#18B) Step3: Attach the SAND CONTROL VALVE to the other end of the NIPPLE CONNECTOR. If the Soda Blaster requires more force to accomplish the task, verify that the Soda Blaster receives sufficient, unobstructed airflow (CFM) and increase the pressure (PSI) output of the regulator up to the maximum air pressure rating of this Soda Blaster. If the nozzle control valve does not shut off completely, then close the air control valve before removing the nozzle. Do not allow pressure to exceed 125 PSI. NEITHER THE MANUFACTURER OR DISTRIBUTOR MAKES ANY REPRESENTATION OR WARRANTY OF ANY KIND TO THE BUYER THAT HE OR SHE IS QUALIFIED TO MAKE ANY REPAI THE PRODUCT, OR THAT HE OR SHE IS QUALIFIED TO REPLACE ANY PARTS OF THE PRODUCT. Repeated or long-term exposure to vibration may cause temporary or permanent physical injury, particularly to the hands, arms and shoulders.
Note: These procedures are in addition to the regular checks and maintenance explained as part of the regular operation of the air-operated Soda Blaster. -----------------
Air consumption for the blaster will be nearly proportional to the pressure being used. Unless you have a very large compressor and a large and aggressive job to do, you would probably never want the media control valve to be wide open. If you feel any symptoms related to vibration (such as tingling, numbness, and white or blue fingers), seek medical advice as soon as possible. The SAND HOSE needs replacing when its side walls develop leaks or show blisters in the surface. 
Tool weight: 57 lbs. At time of this writing the canvas hood and filling funnel are missing. THE MANUFACTURER AND/OR DISTRIBUTOR HAS PROVIDED THE PARTS LIST AND ASSEMBLY DIAGRAM IN THIS MANUAL AS A REFERENCE TOOL ONLY. blaster abrasive pressurized central lb pneumatic freight harbor sand tools sandblasting sandblaster kit blast portable deals pressure kx paint housewares 
esb sabbiatrice pneumatica sandblaster pneumatique sableuse epi eurocem medicalexpo With continuous open air flow the pressure eventually drops and stabilizes at 45-psi with my compressor. MAINTENANCE 1. For grit and dust on or inside the car, doing it outdoors may not make much difference (but it would keep the shop clean). Otherwise, isolate the workpiece to make sure no damage can occur to nearby personal property. WARNING marking concerning Risk of Respiratory Injury. A
+b-|u!n p2wT,BYu.;R^~P\ -`J{tqeojJS+Aj4KAjP Turn on the air compressor according to the manufacturers directions and allow it to build up pressure until it cycles off. Home HARBOR FREIGHT HARBOR FREIGHT 60801/60802 Central Pneumatic Portable Soda Blaster Owners Manual, HARBOR FREIGHT 60801/60802 Central Pneumatic Portable Soda Blaster. 3/8 x 13 air belt sander with accessories (13 pages), 2-3/4" x 17-1/2" air inline sander (15 pages), 6" composite palm grop random orbital santer (16 pages), Air wet Remove entire media discharge assembly slowly, being careful with the Pickup Tube (11) as it may contain residual media which can spill when removed. Record products Serial number Here: _______________________, Note: If product has no serial number, record month and year of purchase instead.Note: Some parts are listed and shown for illustration purposes only, and are not available individually as replacement parts. A loose accessory may detach or break during operation. --------------
Use respiratory protection when source controls cannot keep silica exposures below the NIOSH REL. When unpacking, make sure that the product is intact and undamaged. 
Proof of purchase date and an explanation of the complaint must accompany the merchandise. A broom handle makes a good dipstick for checking media level in the tank. This is how you relieve tank pressure before opening the tank cap to check or refill media material. Harbor freight tools central pneumatic series 40 lb pressurized sandblaster model 34202 assembly and operating instructions, 3491 Mission Oaks Blvd. Step 5: Attach the other WHEEL to the AXLE using the remaining COTTER PINS. I can say right off that open room sand blasting does a nice job of cleaning up blistered paint and rust, but it is a very dirty job. diy sandblaster blaster plans sand soda sandblasting sandblast homemade cabinet tools result pressure pot gun herramientas equipment herreria compressor soldadura Step3: On the top of the WATER TRAP is an arrow. shape or form without the express written consent of Harbor Freight Tools. Also finer grain media will seem to put more dust into the air and obscure visibility. Pregnant women or people who have impaired blood circulation to the hand, past hand injuries, nervous system disorders, diabetes, or Raynauds Disease should not use this tool. WARNING! Greater distance gives a larger blast spot for quicker progress.
Other components, such as a coupler plug and quick coupler, will make operation more efficient, but are not required. For gross removal of paint and rust you may want maximum pressure on the blaster (do not exceed 125 psi safe pressure limit). sand abrasive hVn8>X$"(nHv?U@V6g }(G3:e!V5pWXE$bHCXN`PAVI"d 9cg:Y?)&gF#u8fJj%XVtq gY 5.t:$tCrZM X 01qWn5tsRNiOqG3:HAgeQO&zI !/gFw &r&OW_WYMdI6O CS BE|5v'"obeUv[?4ppc>r[H7IfYIp%~`;]Jn h1q=>[s&!8PZmuz|phZ#>iegI!KxvX TO PREVENT SERIOUSINJURY FROM ACCIDENTAL OPERATION:close all Valves, detach the air supply, safely discharge any residual air pressure in the Soda Blaster, and close all Valves again before performing any procedure in this section. Use tools with the lowest vibration when there is a choice. Poor or irregular flow of the abrasive may also be due to low air pressure or a worn Nozzle. eastwood That pressure is non functional with this unit, but it indicates a rough air consumption figure of 9.0-scfm @ 45-psi. Overall dimensions: 40''H x 24''L x 15''W
Step 1: Check to insure the abrasives are dry and clean so that they do not clog the unit. 
Do not yank compressors cord to disconnect it from the receptacle. Avoid skin exposure. This warranty gives you specific legal rights and you may also have other rights which vary from state to state. The grit goes everywhere, so don't have an open engine or gearbox in the room when doing this. Step 2: Attach the FOOT to the TANK (#1) using one of the COTTER PINS. 497A""
A"TD
.j?,\~gO.v ?@&)34q~: e y@2$J B H- 3"Kd P3. A possible short use alternative is a pillow case with a site hole cut out and fully closed goggles. Inspect compressors cord periodically and, if damaged, have them repaired by an authorized technician. Diagrams within this manual may not be drawn proportionally. We will return repaired products at our expense, but if we determine there is no defect, or that the defect resulted from causes not within the scope of our warranty, then you must bear the cost of returning the product. Open the Media Valve. As such it will work with 50%-60% duty cycle with my compressor, giving one minute of trigger time
DO NOT OVERREACH. BEFORE EACH USE, inspect the general condition of the Soda Blaster. cabinet blast homak abrasive table gallon sandblaster blasting blaster sand tank industrial air Difference is, a ball valve does not shut off automatically if you drop it. Spray the abrasive media onto the work material, moving the Nozzle from side to side. Attempting to blast aluminum sheet panels or soft brass parts is tricky business to be approached at your own risk. Wear ANSI-approved eye protection. Sand Control Valve/ Nozzle Shut Off Valve Refer to Figure 5. Keep in mind that the media tank is also a compressed air tank with a fairly large volume (about 10 gallons). Secure loose workpieces using a vise or clamps (not included) to prevent movement while working. ?,)rD&7hgq/X~s(8$b+>gT ?iadZgg[%C'Btt;LL|D( IEZT{%"F$Z)D?DCS*NEB('TF8*Du1@!d$4 When I finally take the body off the car for underbody painting there will be more grit on the heater shelf, under and around the engine, and on the suspension parts. To reduce vibration, maintain tool as explained in this manual. Step3: Attach the JOINT PIPE (#13) to the upper side port of the TANK (#1). If the blast nozzle becomes clogged during use, immediately close the media control valve at bottom of the tank. I was walking around in the grit and not wanting to touch anything. Obey the manual for the air compressor used to power this Soda Blaster. It may be appropriate to order a replacement hose for the inside of this control head, along with a few spare ceramic nozzles. blower The nozzle control valve on this unit has a thin wall rubber hose inside of a heavy plastic housing. Sand Outlet Manifold (#22) Nipple Connector Step4: Attach the other NIPPLE CONNECTOR (#16) to the other end of the SAND CONTROL VALVE. Read the ENTIRE IMPORTANT SAFETY INFORMATION section at the beginning of this manual including all text under subheadings therein before set up or use of this product. HWr6CD0q/GVZwZ;Zku$JY n;i@bqX. Step2: Attach the PRESSURE GAUGE to the top of the INTAKE MANIFOLD. Turn PRESSURE GAUGE so that its face is over the lower side hold of the INTAKE MANIFOLD. I would say read the entire user's manual, except that it is missing, so my best advice now is to read this entire memo before using the sand blaster. The pipe then splits with one pipe going to pressurize the media tank. 23n`H`3`0c`0u#"2W/
3f@4. The tank can hold up to 110 pounds of abrasive material. Likewise, always open the air control valve before opening the media control valve. 
Personal Equipment, Dirt and Cleanup:
Read and understand the 10 recommended measures below to reduce crystalline silica exposures in the workplace and prevent silicosis and silicosis related deaths. If you close all the valves and walk away it is likely to lose tank pressure through the media control valve and blast head. Nipple Connector (#16) Joint Pipe (#13) Air Cap (#12) Gasket (#11) Tank (#1) Nipple Connector (#16) Air Hose (#21) Figure 6 Top Assembly Step1: Get the Intake Valve Assembly, the Water Trap Assembly, the Tank Assembly, the TANK CAP (#12), the O-RING (#11), and the AIR HOSE (#21). Figuring about 2/3 pound of abrasive use for each minute of trigger time, a full tank could keep you working for 165 minutes of continuous use. ASSEMBLY NOTE: Use Teflon Pipe Tape on all threaded joints. Follow instructions for lubricating and changing accessories. The shop vac will clean a smooth floor in a single pass. The media control valve at the bottom of the tank seems to leak a little when shut off, probably due to being constantly exposed to the abrasive material. There will be no attempt here to turn an amateur blast operator into a skilled professional by words alone. Step2: Slide the HOSE CLAMPS over either side of the SAND HOSE. Right Handle (#6-R) Handle Grip (#7) Handle Bar Left Handle (#6) (#6-L) Screw (#8) Washer (#31) Nut (#9) Figure 7 Handle Bar Assembly Step1: Get out the two HANDLE BARS (#6), the two HANDLE GRIPS (#5), the four SCREWS (#8), four NUTS (#9), and four WASHERS (#31). Insert the Pickup Tube into the Tank and tighten the Bushing. DO NOT ABUSE THE POWER CORD. I didn't like the heavy handed operation of the control lever, so this may be better if it was changed to a ball valve. There is an air supply shut-off valve at the input air coupler, followed by a water separator filter and pressure gauge. WARNING! It is used to alert you to potential personal injury hazards. Wear NIOSH-approved dust mask/respirator. abrasive capacity for big jobs. This may sound like a lot of fiddling, but you should soon learn to regulate and limit the media flow to minimize clogging of the blast head. (Wrenches not included. @ Y
endstream
endobj
40 0 obj
<>
endobj
41 0 obj
<>/Font<>/ProcSet[/PDF/Text/ImageC/ImageI]/XObject<>>>/Rotate 0/Type/Page>>
endobj
42 0 obj
<>
endobj
43 0 obj
<>
endobj
44 0 obj
<>
endobj
45 0 obj
<>
endobj
46 0 obj
[/Indexed 61 0 R 255 63 0 R]
endobj
47 0 obj
[/ICCBased 59 0 R]
endobj
48 0 obj
<>
endobj
49 0 obj
<>stream
if any problems are found, do not use Soda Blaster until repaired. Wear washable or disposable protective clothes at the work site. sandblaster hopper gun Efficient pressurized blaster moves abrasives at 80 to 90 percent of air speed for real blasting power. Instructions Pertaining To A Risk Of Fire, Electric Shock, Or Injury To Persons. Release the collar. j"V09ZG&:>V x73K1b$&h88YpCi OfM+~'g%af%0CA &[q-gzrd
2@.l*8U\ZIRB)Cj%YDq(?RI%:e\jJ;s4/7R>MM3\BqRT+8OiI&%C3 ^oJ:OaBw!+j={O%IvOmM44eCi4g{P8/s@
n' VO~%q Coarser material tends to clog up the nozzle on smaller blaster units (including this one). hb```"3 Ab@Oa{$TXRZM
w(2OLyT0kWG;DW
O',s8V,a0If"m^"[=%$raD1CbE Inspect Soda Blaster before use, looking for damaged, loose, and missing parts. SAVE THIS MANUAL You will need the manual for the safety warnings and cautions, assembly instructions, operating procedures, maintenance procedures, trouble shooting, parts list, and diagram. At 50 psi this unit stops supplying abrasive material. Post signs to warn workers about the hazard and to inform them about required protective equipment. 
Wear suitable gloves to reduce the vibration effects on the user. Removing heavy rust from steel parts is a cinch, as it can ultimately remove steel from steel parts. If you have a smaller compressor (less than 15-scfm supply), there may be large swings in system pressure during use. Always wear your hood, dust mask, and heavy-duty canvas Step 2: Close the AIR SUPPLY VALVE (#18) by turning it to gloves when operating the the horizontal position. 11. Pull back on the blue Air Hose Connector (8) collar and pull out Air Hose (15). Proper ventilation in the work area is required. Use containment methods such as blast-cleaning machines and cabinets to control the hazard and protect adjacent workers from exposure. sandblaster abrasives Exposure to aluminum oxide (a dust generated from material removing processes) can result in eye, skin and breathing irritation. Trouble shooting:
Drain the moisture filter regularly. Step 4: Slide the AXLE through the hole in the bottom of the two HANDLE BARS (#6). Parts may not be interchangeable. MAINTAIN TOOLS WITH CARE. followed by one minute of pressure recovery time for the compressor. Do not use sand or other blasting materials that contain crystalline silica.Note: Use only dry and clean abrasives to avoid clogging the Soda Blaster.Note: The Nozzle size depends on grit of media used. This setup had a problem when I first used it, as the blast head would sometimes clog easily and repeatedly. Make sure all joints are securely tighten. angle sander polisher angle sander polisher angle sander polisher (10 pages), 6" self-vacuuming air palm sander (16 pages), Heavy duty air oscillating sander (11 pages), Manual will be automatically added to "My Manuals", Assembly and operating instructions manual, Sand Control Valve/ Nozzle Shut off Valve, Sander Central Pneumatic 35245 Assembly And Operating Instructions Manual, Sander Central Pneumatic CENTRAL PNEUMATIC 91773 Owner's Manual, Sander Central Pneumatic 66881 Set Up And Operating Instructions Manual, Sander Central Pneumatic 68152 Owner's Manual And Safety Instructions, Sander Central Pneumatic 93629 Assembly And Operating Instructions Manual, Sander Central Pneumatic 93742 Assembly And Operating Instructions Manual, Sander Central Pneumatic 42966 Assembly And Operating Instructions Manual, Sander Central Pneumatic 97055 Set Up And Operating Instructions Manual, Sander Central Pneumatic 91773 Set Up And Operating Instructions Manual, Sander Central Pneumatic 65173 Set Up And Operating Instructions Manual, Sander Central Pneumatic 93050 Assembly And Operating Instructions Manual, Sander Central Pneumatic 98895 Owner's Manual & Safety Instructions, Sander Central Pneumatic 96989 Set Up And Operating Instructions Manual, Sander Central Pneumatic 96445 Operation Instructions Manual, Sander Central Pneumatic 96573 Set Up And Operating Instructions Manual. Sand Control Valve (#18B) Step3: Attach the SAND CONTROL VALVE to the other end of the NIPPLE CONNECTOR. If the Soda Blaster requires more force to accomplish the task, verify that the Soda Blaster receives sufficient, unobstructed airflow (CFM) and increase the pressure (PSI) output of the regulator up to the maximum air pressure rating of this Soda Blaster. If the nozzle control valve does not shut off completely, then close the air control valve before removing the nozzle. Do not allow pressure to exceed 125 PSI. NEITHER THE MANUFACTURER OR DISTRIBUTOR MAKES ANY REPRESENTATION OR WARRANTY OF ANY KIND TO THE BUYER THAT HE OR SHE IS QUALIFIED TO MAKE ANY REPAI THE PRODUCT, OR THAT HE OR SHE IS QUALIFIED TO REPLACE ANY PARTS OF THE PRODUCT. Repeated or long-term exposure to vibration may cause temporary or permanent physical injury, particularly to the hands, arms and shoulders.
Note: These procedures are in addition to the regular checks and maintenance explained as part of the regular operation of the air-operated Soda Blaster. -----------------
Air consumption for the blaster will be nearly proportional to the pressure being used. Unless you have a very large compressor and a large and aggressive job to do, you would probably never want the media control valve to be wide open. If you feel any symptoms related to vibration (such as tingling, numbness, and white or blue fingers), seek medical advice as soon as possible. The SAND HOSE needs replacing when its side walls develop leaks or show blisters in the surface. Tool weight: 57 lbs. At time of this writing the canvas hood and filling funnel are missing. THE MANUFACTURER AND/OR DISTRIBUTOR HAS PROVIDED THE PARTS LIST AND ASSEMBLY DIAGRAM IN THIS MANUAL AS A REFERENCE TOOL ONLY. blaster abrasive pressurized central lb pneumatic freight harbor sand tools sandblasting sandblaster kit blast portable deals pressure kx paint housewares esb sabbiatrice pneumatica sandblaster pneumatique sableuse epi eurocem medicalexpo With continuous open air flow the pressure eventually drops and stabilizes at 45-psi with my compressor. MAINTENANCE 1. For grit and dust on or inside the car, doing it outdoors may not make much difference (but it would keep the shop clean). Otherwise, isolate the workpiece to make sure no damage can occur to nearby personal property. WARNING marking concerning Risk of Respiratory Injury. A
+b-|u!n p2wT,BYu.;R^~P\ -`J{tqeojJS+Aj4KAjP Turn on the air compressor according to the manufacturers directions and allow it to build up pressure until it cycles off. Home HARBOR FREIGHT HARBOR FREIGHT 60801/60802 Central Pneumatic Portable Soda Blaster Owners Manual, HARBOR FREIGHT 60801/60802 Central Pneumatic Portable Soda Blaster. 3/8 x 13 air belt sander with accessories (13 pages), 2-3/4" x 17-1/2" air inline sander (15 pages), 6" composite palm grop random orbital santer (16 pages), Air wet Remove entire media discharge assembly slowly, being careful with the Pickup Tube (11) as it may contain residual media which can spill when removed. Record products Serial number Here: _______________________, Note: If product has no serial number, record month and year of purchase instead.Note: Some parts are listed and shown for illustration purposes only, and are not available individually as replacement parts. A loose accessory may detach or break during operation. --------------
Use respiratory protection when source controls cannot keep silica exposures below the NIOSH REL. When unpacking, make sure that the product is intact and undamaged. Proof of purchase date and an explanation of the complaint must accompany the merchandise. A broom handle makes a good dipstick for checking media level in the tank. This is how you relieve tank pressure before opening the tank cap to check or refill media material. Harbor freight tools central pneumatic series 40 lb pressurized sandblaster model 34202 assembly and operating instructions, 3491 Mission Oaks Blvd. Step 5: Attach the other WHEEL to the AXLE using the remaining COTTER PINS. I can say right off that open room sand blasting does a nice job of cleaning up blistered paint and rust, but it is a very dirty job. diy sandblaster blaster plans sand soda sandblasting sandblast homemade cabinet tools result pressure pot gun herramientas equipment herreria compressor soldadura Step3: On the top of the WATER TRAP is an arrow. shape or form without the express written consent of Harbor Freight Tools. Also finer grain media will seem to put more dust into the air and obscure visibility. Pregnant women or people who have impaired blood circulation to the hand, past hand injuries, nervous system disorders, diabetes, or Raynauds Disease should not use this tool. WARNING! Greater distance gives a larger blast spot for quicker progress.
